Page 1 of 1 1
Topic Options
Rate This Topic
#192503 - 05/18/18 10:15 PM 445 Super Mag Reloading Question
amanda121287
stranger


Registered: 05/18/18
Posts: 1

Offline
Before I order reloading dies, I just want to make sure. Can I use 44SPCL/44Mag dies of ANY company to reload my 445, or only certain ones. Thanks in advance.


Edited by amanda121287 (05/18/18 10:16 PM)

Top
#192507 - 05/19/18 10:22 AM Re: 445 Super Mag Reloading Question [Re: amanda121287]
JDK
enthusiast


Registered: 01/18/04
Posts: 216
Loc: Texas Hill Country

content Online
I have personally used Lee .38\357 dies to load 357 Maximum\Supermag. As I understand it, they will all work, but I'm sure others can clarify that info.


Edited by JDK (05/19/18 10:22 AM)
_________________________
John

But for the grace of God, there, I go.

Top
#192508 - 05/19/18 10:23 AM Re: 445 Super Mag Reloading Question [Re: amanda121287]
Mech 8
member


Registered: 08/30/11
Posts: 190
Loc: San Antonio, TX

Offline
I have used a Lee 44 Mag die set to reload 445 Super mag. I just happened to have a set of these dies and they worked for me. I will suggest that you apply a little case lube to the brass even though the die is carbide. I found this out the hard way using a Lee carbide sizer for 41 Mag to resize my 414 Super mag cases. After about 15 to 20 cases, I ran one up into the die and it didn't want to come back out. Ended up pulling the carbide ring out of the die trying to remove the case. I seem to recall a mention of using lube on the longer cases way back in my mind, but of course didn't recall it till after I ruined my die. Good luck with the 445, it is pretty potent.

Top
#192509 - 05/19/18 03:37 PM Re: 445 Super Mag Reloading Question [Re: Mech 8]
OFFSHORE
member


Registered: 12/10/17
Posts: 100

Offline
I'm using .44 Rem Mag dies from Redding for my 445 SM. I use a decaping die first for primer removal then resize about 3/16" of the case with sizer die, only because the decaping rod set this way will not punch out the primer. I'm shooting a .431" hardcast bullet in Starline brass and even on fired cases you can't slide a bullet in, so the little bit of sizing and a good heavy crimp does quite well. You could spend the extra $100-$125 dollars and wait time for a 445 SM set to be made, but you should be fine with several of the 44 Rem Mag dies out there. I've just been getting started in the 445 SM realm and find it to be a very accurate and nice shooting cartridge. Good luck and enjoy.

Top
#192519 - 05/20/18 05:23 PM Re: 445 Super Mag Reloading Question [Re: OFFSHORE]
Mad Dog 1954
enthusiast


Registered: 10/26/10
Posts: 241
Loc: Southern Indiana

Offline
Yep I use 44 mag dies works fine
_________________________
Sometimes it is entirely appropriate to kill a fly with a 12 pound sledgehammer!

Top
#193080 - 06/17/18 07:30 AM Re: 445 Super Mag Reloading Question [Re: Mad Dog 1954]
OFFSHORE
member


Registered: 12/10/17
Posts: 100

Offline
amanda 121287;

Any progress yet? Just courious, not much 445 SM talk around here and I want to hear some.

Top
Page 1 of 1 1


Moderator:  Gary, jamesfromjersey, Chance Weldon, Gregg Richter 
Hop to:
 Portal Sidebar
Who's Online
5 registered (karl, JDK, Bob Roach, Gregg Richter, SacredCrows) and 172 anonymous users online.
Top Posters
9608
s4s4u
9273
Whitworth
8687
jamesfromjersey
7643
wapitirod
7327
TCTex.
6324
KRal
5056
Gary
5006
Ernie
4704
Tigger
4461
pab1
4370
Dan B.
4124
Chance Weldon
4070
Gregg Richter
3972
Franchise
3755
johnwilliams
  Member Hunts
Gerry and Mike's E
Gerry and Mike's Elk Hunting adventure

Contender & Encore
Contender & Encore Estimated Manufacturing Dates

   Access Requires Login

Generated in 0.022 seconds in which 0.002 seconds were spent on a total of 14 queries. Zlib compression enabled.




Copyright © 2000-2008
HandgunHunt.com, Inc.